Prevista Dry mounting unit
Product information
Prevista Dry mounting unit
for Prevista Dry elements with hole size 390 mm or 460 mm
| Year built (from): | 01.12.2022 |
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and plumbing experts and trained personnel
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Standards and regulations
The following standards and regulations apply to Germany / Europe and are provided as a support feature.
Regulations from section: Fields of application / Mounting conditions
Scope / Notice | Regulations applicable in Germany |
|---|---|
Suitable masonry walls | EN 1996‑1‑1 |
Suitable concrete walls | DIN 1045 |
Product description
Overview
- 1 Prevista Dry mounting unit
- 2 Fixing material for element
- 3 Compensating pieces
- 4 Fixing material for wall
Accessories
Mounting profile 45° (model 8077) for cladding on self-supporting wall and for corner mounting to the left and right of the element.
Mounting profile 90° (model 8076) for cladding on self-supporting wall.
Handling
Assembly information
Installation dimensions
Assembly
Mounting the mounting unit
INFO!
Only models with a 3H cistern can be used for Prevista Dry WC elements.
The corner valve must always be inserted into the cistern from behind.
Mounting on a self-supporting wall
-
Screw the Prevista Dry element to the Prevista Dry mounting unit.
Tightening torque: maximum 30 Nm
-
Align the Prevista Dry element.
-
Determine and mark the fixing points on the wall and on the floor.
-
Drill the holes.
-
Insert the dowels.
-
Align the Prevista Dry element according to its instructions for use and screw it tight.
Mounting in a room corner
-
Screw the Prevista Dry element to the Prevista Dry mounting unit.
Tightening torque: maximum 30 Nm
-
Determine and mark the fixing points.
-
Drill the holes.
-
Insert the dowels.
-
If the angle of the room corner is > 90°, adjust the angle using the compensating pieces.
-
Align the Prevista Dry element according to its instructions for use and screw it tight.
Cladding the element
Cladding on a self-supporting wall
-
Mount the mounting profile 90° flush to the wall.
-
Mount the mounting profile 45° flush to the first corner of the Prevista Dry mounting unit.
-
Clad the element with suitable plasterboard cladding panels.
-
Mount the mounting profile 45° flush to the second corner of the Prevista Dry mounting unit.
-
Clad the element with suitable plasterboard cladding panels.
-
Clad the rest of the element with suitable plasterboard cladding panels.
Cladding in a room corner
-
Mount the mounting profiles 45° flush to the Prevista Dry mounting unit.
-
Clad the element with suitable plasterboard cladding panels.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.