Sink basin module
Product information
Sink basin module
for sink basins
| Year built (from): | 05.03.2009 |
Trade mark rights exist for this document, further information can be found at viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and sanitary professionals and trained personnel
SHK-FachkräfteConsumers
It is not permitted for individuals without the abovementioned training or qualification to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
INFO!
Notes give you additional helpful tips.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Standards and regulations
The following standards and regulations apply to Germany / Europe. National regulations can be found on the relevant web site of your country at viega.com/standards .
Regulations from section: Fields of application / Mounting conditions
Scope / Notice | Regulations applicable in Germany |
|---|---|
suitable masonry walls | EN 1996‑1‑1 |
suitable concreted walls | DIN 1045 |
Regulations from section: Sound protection
Scope / Notice | Regulations applicable in Germany |
|---|---|
Fulfilled noise protection requirements | DIN 4109 |
Fulfilled noise protection requirements | DIN 4109 (additional sheet 2) |
Fulfilled noise protection requirements | VDI 4100 SSt I-SSt II |
Product description
Overview
- 1 - slot nut
- 2 - sink basin
- 3 - mounting bracket for drain elbow
- 4 - drain elbow
Compatible components
The module is compatible with all common sink basins.
Sound protection
The sink basin element complies with the noise insulation requirements specified in section Regulations from section: Sound protection .
Handling
Assembly information
Mounting conditions
Suitable walls
For this, observe the Steptec system instructions for use.
Construction height
With the construction height, the marked height of the upper edge of the finished floor must be observed.
Installation dimensions
Required tools
The following tools are required for mounting:
fork or ring spanner: 17 mm / 19 mm
Phillips-tip screwdriver
Assembly
Mounting module
Mounting in Steptec
INFO!
The two vertical rails, which surround the module, must be open towards the module and be at an interval of 430 mm.
-
Secure the module onto the open Steptec rail with the slot nuts supplied:
-
Insert the slot nut into the opening.
-
Push the slot nut in slightly.
-
Turn by 90°.
-
The slot nut is secured in the Steptec rail.
-
Align the height of the module.
-
Tighten the slot nut with a ring spanner (SW 17).
-
Tighten the other slot nuts in the same way.
-
The module is secured on the rail framework.
-
Place the drain elbow in the intended bracket.
-
Close the bow around the drainpipe.
-
Set the desired height for the drain elbow.
Tighten the screws with a Phillips screwdriver.
-
Check height settings.
When doing so, observe the sink basin's manufacturer's instructions (X).
-
Make sure that the fixing ends flush with the rail framework. The fixing may extend for a maximum of 1.5 mm beyond the rail framework.
Do not unscrew the screws completely.
-
Set the distance from the drain elbow to the sink basin module using the two middle screws on the module.
To do this, loosen the screws slightly and set the desired height.
Re-tighten screws.
Rounding off jobs
-
Single clad pre-wall: Clad with 12.5 mm wide IFGP or 12 mm wide Aqua-KS cladding panels.
When doing so, make sure that no abutting edges converge.
-
Grout the abutting edges and joints with a suitable filler.
-
Observe the instruction manual for the cladding panels for more information.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.